01995D0467 — EN — 10.11.2010 — 003.001


This text is meant purely as a documentation tool and has no legal effect. The Union's institutions do not assume any liability for its contents. The authentic versions of the relevant acts, including their preambles, are those published in the Official Journal of the European Union and available in EUR-Lex. Those official texts are directly accessible through the links embedded in this document

►B

COMMISSION DECISION

of 24 October 1995

implementing Article 20 (2) of Council Directive 89/106/EEC on construction products

(Text with EEA relevance)

(95/467/EC)

(OJ L 268 10.11.1995, p. 29)

Amended by:

 

 

Official Journal

  No

page

date

►M1

COMMISSION DECISION  of 8 January 2001

  L 209

33

2.8.2001

►M2

COMMISSION DECISION  of 15 July 2002

  L 192

57

20.7.2002

►M3

COMMISSION DECISION  of 8 November 2010

  L 292

55

10.11.2010




▼B

COMMISSION DECISION

of 24 October 1995

implementing Article 20 (2) of Council Directive 89/106/EEC on construction products

(Text with EEA relevance)

(95/467/EC)



Article 1

The products and families of products set out in Annex 1 shall have their conformity attested by a procedure whereby the manufacturer has under its sole responsibility a factory production control system ensuring that the product is in conformity with the relevant technical specifications.

Article 2

The products set out in Annex 2 shall have their conformity attested by a procedure whereby, in addition to a factory production control system operated by the manufacturer, an approved certification body is involved in the assessment and surveillance of the production control or of the product itself.

Article 3

The procedure for attesting conformity as per Annex 3 shall be given in mandates for harmonized standards.

Article 4

This Decision is addressed to the Member States.




ANNEX 1

— 
Chimneys, flues and specific products: chimney terminals.
— 
Gypsum products: plasterboards, blocks, ceiling elements and plasters, including the relevant ancillary products, different from those mentioned in Annex 2.
— 
Structural bearings: all types of structural bearings intended to be used in buildings and civil engineering works where requirements on individual bearings are not critical ( 3 ).




ANNEX 2

— 
Chimneys, fuels and specific products: prefabricated chimneys (storey height elements), flue liners (elements or block), multi-shell chimney (elements or block), single walled chimneys blocks, kits of free standing chimneys and attached chimneys.
— 
►M1  
Plasterboards and ceiling elements with thin laminations, fibrous gypsum boards and composite panels, including relevant ancillary products, falling into classes A1 ( 4 ), A2 (4) , B (4) , C (4)  and intended to be used in walls, ceilings (or linings thereof) subject to reaction to fire requirements.
 ◄
— 
Structural bearings: all types of structural bearings intended to be used in buildings and civil engineering works where requirements on individual bearings are critical ( 5 ).




ANNEX 3

PRODUCT FAMILY:

CHIMNEYS, FLUES AND SPECIFIC PRODUCTS (1/1)

Systems of attestation of conformity

For the product(s) and intended use(s) listed below, European Committee for Standardization, European Committee for Electrotechnical Standardization (CEN/Cenelec) are requested to speciy the following system(s) of attestation of conformity in the relevant harmonized standard(s):



Product(s)

Intended use(s)

Level(s) or class(es)

(Reaction to fire) (1)

Attestation of conformity system(s)

Prefabricated chimneys (storey height elements), flue liners (elements or blocks), multi-shell chimney (elements or blocks), single walled chimneys blocks, kits of free standing chimneys and attached chimneys

Chimneys

►M1  Any ◄

2 + (2)

Chimney terminals

Chimneys

►M1  Any ◄

4 (3)

▼M3

Prefabricated chimneys (storey height elements), flue liners (elements or blocks), multi-shell chimney (elements or blocks), single walled chimneys blocks, kits of free standing chimneys and attached chimneys, chimney terminals

For uses subject to regulations on reaction to fire

(A1, A2, B, C) (*1)

1

(A1, A2, B, C) (*2), D, E

3

(A1 to E) (*3), F

4

▼B

(1)   

For reaction to fire, see ►M1  Commission Decision 2000/147/EC (OJ L 50, 23.2.2000, p. 14) ◄ .

(2)   

System 2 +: See Directive on construction products (CPD) Annex III.2.(ii), first possibility, including certification of the factory production control by an approved body on the basis of its continuous surveillance, assessment and approval.

(3)   

System 4: CPD Annex III.2.(ii), third possibility.

(*1)   

Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material).

(*2)   

Products/materials not covered by footnote *.

(*3)   

Products/materials that do not require to be tested for reaction to fire (e.g. Products/materials of Class A1 according to Commission Decision 96/603/EC, OJ L 267, 19.10.1996, p. 23).

 ◄

System 1: See Directive 89/106/EEC, Annex III(2)(i), without audit-testing of samples.

System 3: See Directive 89/106/EEC, Annex III(2)(ii), second possibility.

System 4: See Directive 89/106/EEC, Annex III(2)(ii), third possibility.

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

PRODUCT FAMILY:

GYPSUM PRODUCTS (1/4)

Systems of attestation of conformity

For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):



Product(s)

Intended use(s)

Level(s) or class(es)

(Reaction to fire of incorporated materials) (1)

Attestation of conformity system(s)

Plasterboards and ceiling elements with thin laminations, fibrous gypsum boards, ►M2  fibrous gypsum plaster casts ◄ and composite panels (laminates) in which the incorporated material is placed on a face susceptible to be exposed to fire, including relevant ancillary products

In walls, partitions or ceilings (or lining thereof) subject to reaction to fire requirements

►M1  A1 (2), A2 (2), B (2), C (2)  ◄

►M1  A1 (3), A2 (3), B (3), C (3), D, E ◄

►M1  (A1 to E) (7), F ◄

1 (4)

3 (5)

4 (6)

(1)   

For reaction to fire, see ►M1  Commission Decision 2000/147/EC (OJ L 50, 23.2.2000, p. 14) ◄ .

(2)   

►M1  Products/materials for which a clearly identifiable stage in the production process results in any improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material) ◄ .

(3)   

►M1  Products/materials not covered by footnote (2) ◄ .

(4)   

System 1: See CPD Annex III.2.(i), without audit-testing of samples.

(5)   

System 3: See CPD Annex III.2.(ii), Second possibility.

(6)   

System 4: See CPD Annex III.2.(ii), third possibility.

►M1  (7)   

Products/materials that do not require to be tested for reaction to fire (e.g. Products/materials of Classes A1 according to Commission Decision 96/603/EC).

 ◄

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

PRODUCT FAMILY:

GYPSUM PRODUCTS (2/4)

Systems of attestation of conformity

For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):



Product(s)

Intended use(s)

Level(s) or class(es)

(Resistance to fire)

Attestation of conformity system(s)

Plasterboards, blocks, ceiling elements and gypsum plasters, ►M2  fibrous gypsum plaster casts, ◄ including relevant ancillary products

In walls, partitions or ceilings, as relevant, intended for fire protection of structural elements and/or fire compartmentation in buildings

Any

3 (1)

(1)   

System 3: See CPD, Annex III.2.(ii), second possibility.

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

PRODUCT FAMILY:

GYPSUM PRODUCTS (3/4)

Systems of attestation of conformity

For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):



Product(s)

Intended use(s)

Level(s) or class(es)

Attestation of conformity system(s)

Plasterboards, including relevant ancillary products

For stiffening timber-framed windloadbearing walls or timber roof struss structures

—

3 (1)

(1)   

System 3: See CPD Annex III.2.(ii), second possibility.

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

PRODUCT FAMILY:

GYPSUM PRODUCTS (4/4)

Systems of attestation of conformity

For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):



Product(s)

Intended use(s)

Level(s) or class(es)

Attestation of conformity system(s)

Plasterboards, blocks, ceiling elements and plasters, ►M2  fibrous gypsum plaster casts, ◄ including relevant ancillary products

In walls, partitions or ceilings, as relevant, for situations and uses not mentioned in (1/4), (2/4) or (3/4)

—

4 (1)

(1)   

System 4: See CPD Annex III.2.(ii), third possibility.

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

PRODUCT FAMILY:

STRUCTURAL BEARINGS (1/1)

Systems of attestation of conformity

For the product(s) and intended use(s) listsed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):



Product(s)

Intended use(s)

Level(s) or class(es)

Attestation of conformity system(s)

Structural bearings

In buildings and civil engineering works where requirements on individual bearings are critical (1)

 

1 (3)

In buildings and civil engineering works where requirements on individual bearings are not critical (2)

 

3 (4)

(1)   

‘Critical’ in the sense that those requirements may, in case of failure of the bearing, put the works or parts thereof in states beyond those regarded as serviceability and ultimate limit states.

(2)   

‘Not critical’ in the sense that those requirements may not, in case of failure of the bearing and under normal circumstances, put the works or parts thereof in states beyond those regarded as serviceability and ultimate limit states.

(3)   

System 1: See CPD Annex III.2.(i), without audit-testing of samples.

(4)   

System 3: See CPD Annex III.2.(ii), second possibility.

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.



( 1 )  OJ No L 40, 11.2.1989, p. 12.

( 2 )  OJ No L 220, 31.8.1993, p. 1.

( 3 ) Not critical in the sense that those requirements may not, in case of failure of the bearing and under normal circumstances, put the works or parts thereof in states beyond those regarded as serviceability and ultimate limit states.

( 4 ) Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material).

( 5 ) Critical in the sense that those requirements may, in case of failure of the bearing, put the works or parts thereof in states beyond those regarded as serviceability and ultimate limit states.